Best laser for mac 10 9mm full#

The MAC10 performs similarly to the Colt SMG and Kriss Vector, being more close-quarters-combat (CQC) oriented. Its range, recoil, and low minimum damage limit its ability to perform outside of CQC.ĭue to the high RoF, the MAC10 has a high rate of ammunition consumption, which means reloads are often frequent.

Best laser for mac 10 9mm full#

It acts as a balance between hipfire and full ADS, the spread being somewhere in the middle of the two. This makes aiming less accurate without the aid from a laser, but this mode has less visual recoil, which is useful in some situations. Pressing the alternate aim button will rotate the weapon 45 degrees when ADS. The MAC10 also sports an alternative aiming mode. The good hipfire stability makes up for this however, as the MAC10 is geared towards close quarters, so hipfiring is a viable alternative to ADS. The higher recoil of the MAC10 hampers its performance while aiming down sights (ADS) and subsequently its usage beyond very close range. It has one of the shortest effective ranges in-game. Its maximum damage is only dealt out until 20 studs, being very poor for its class. Its low minimum damage of 19 already makes long range engagements difficult, but this is exacerbated by its range. However, even at a short range, the MAC10 will suffer a lot more than most PDWs. When combined with the high RoF, the time to kill (TTK) for the MAC10 up close is extremely low, the lowest of any automatic weapon in-game. Its maximum damage value is the second highest out of all the PDWs, being able to achieve a 2SK to the head, like the UMP45. Much like the Colt SMG it has a three-shot kill (3SK) up close and a 6SK with minimum damage. The MAC10 possess a high rate of fire (RoF) of 1090 RPM, just above the Colt SMG 633's 1000 RPM. In order to reduce costs, the weapon uses the same 30-round box magazine as the M3A1. The weapon also features a telescoping bolt, similar to the Israeli Uzi, which allows the weapon to be more compact than older submachine guns. The weapon's construction mainly consists of stamped steel. However, the weapon is also much harder to conceal as a result. It significantly reduces the noise and makes the weapon easier to control. 380 ACP or 9 ×17mm.Ī proprietary two-stage suppressor was created for this weapon, made by Sionics. A smaller variant called the MAC-11 is chambered in. It is chambered in the 9x19mm Parabellum or the. Ingram in 1964 and manufactured by Military Armament Corporation from 1970-1973. The MAC-10 ( Military Armament Corporation Model 10), officially designated as the M-10, is a compact, blowback-operated machine pistol developed by Gordon B. It is unlocked at rank 23, or it can be purchased with credits. So the lens’s size is not the larger the better, we should consider the relevant wattage of the fiber laser source’s power equipped.The MAC10 is an American Personal Defense Weapon. If we use the 20W for 175 x 175 mm, of course, the machine also could mark engrave on the subject, but the edge may not be marked or engraved well, as bigger working area is,longer distance will be so the laser bean has been weaken.

If the marking area 175 x 175 mm or 200 x 200 mm, the wattage of the fiber laser source must be at least 30W or 20w for 110x110 +adding extra lens with 175 x 175 mm if with low budget.Then what configuration should be equipped to fulfill the needs and best accurate marking engraving demands? Usually, the marking engraving within 110 x 110 mm area is enough for most kinds of laser marking engraving application needs.įiber Laser Engraver with working size 110*110mmīut a few customers need to engraving marking some bigger patterns or logos sizes than 175 x 175 mm or 200 x 200 mm, even 300 x 300 mm. As we know, the normal configuration of a fiber marker engraver is 20W power with 110 x 110 mm lens.